®
Gas Dryer
DOOR CLEARANCE
DIMENSIONS
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
3-7/8"
GGN2000H LGQ8858H LGR5600H LGR7646J
GGQ9858J LGQ8858J LGR5600J LGR8857E
LGC8858E LGR3624E LGR5636E LGR8858E
LGN1000H LGR3624J LGR5636J LGT7646E
LGQ8800J LGR3634E LGR5644E LGW8858H
LGQ8857H LGR3634J LGR5644J
22-3/4"
19-1/8"
LGQ8857J LGR4634E LGR5848E
22-3/4"
14-1/2"
Gas supply: Dryer is equipped for use with
NATURAL gas. Dryer can be converted to L.P. gas.
When rigid pipe is used it should be 1/2 inch IPS.
When acceptable to the gas supplier and local
codes, 3/8-inch approved tubing may be used for
lengths under 20 feet. For lengths over 20 feet,
larger tubing should be used. Pipe-joint
dryer exhaust
vent
Super-large
side-swing door (reversible)
7"
42-3/8"*
2-1/8"
6"*
9-1/4"
22-3/4"
gas burner inlet
pipe connection
at rear of dryer
compounds resistant to the action of L.P. gas must
be used. If local codes permit, it is recommended
that new flexible metal tubing, design-certified by
AGA or CSA, be used for connecting the appliance
to the rigid gas supply line. (The gas pipe which
extends through the lower rear of the appliance
has 3/8-inch male pipe thread.) An individual
manual shutoff valve must be installed within 6
feet of the dryer in accordance with the National
Fuel Gas Code ANSI Z223.1.
17-3/4"
29"
28" max.**
22-3/4"
Large side-swing
door (reversible)
* from floor with dryer feet extended 1 inch
** Most installations will require at least 5-inch clearance
behind the dryer for the dryer vent.
8-1/4"
15-1/4"
Electrical: 120-volt, 60-Hz,
RECESSED AREA AND CLOSET INSTALLATION
AC-only, 15- or 20-amp.
electrical supply. Use copper
wire only. A time-delay fuse
or circuit breaker and
separate circuit is
15-1/4"
15-1/4"
Closet confined area
Recessed
area
If a closet door is installed: The minimum unobstructed
air openings are required. Louvered doors with equivalent
air openings are acceptable.
recommended.
front view
front view
side view
Small side-swing door
Exhaust venting: Exhaust
your dryer to the outside.
four-inch diameter vent is
required. Rigid or flexible
metal exhaust vent must be
used. Do Not use plastic or
metal foil vent. Exhaust outlet
hood must be at least 12
inches from the ground or
any object that may be in the
path of the exhaust.
3"
8-3/4"
25-5/8"
14"
48 sq. in.*
24 sq. in.*
max.
closet
door
18"
13-3/4"
4" **
3"
13-3/4"
Extra-large hamper door
1"
0"***
0"***
* Minimum top and bottom air openings for closet door.
**External exhaust elbow requires additional space.
***Wall, door and floor molding
may require additional spacing.
EXHAUST VENTING
Select the route that will provide the straightest and most direct path outdoors. Plan the
installation to use the fewest number of elbows and turns. Avoid making 90° turns.
When using elbows or making turns, allow as much room as possible. Bend flexible
metal vent gradually to avoid kinking.
Acceptable
Preferred
4"
4"
2-1/2"
Determine vent length
When you have a 4" hood
When you have a 2-1/2" hood
1. See the exhaust vent length chart that matches your type hood for the maximum vent
lengths you can use.
Do not use vent runs longer than specified in exhaust vent length charts.
Maximum length of 4"
diameter metal vent
Maximum length of 4"
diameter metal vent
Number of
90° elbows
Rigid
Flexible
(fully extended)
Number of
90° elbows
Rigid
Flexible
(fully extended)
2. Determine the number of elbows you will need.
0
1
2
3
4
64 ft.
54 ft.
44 ft.
35 ft.
27 ft.
36 ft.
31 ft.
27 ft.
25 ft.
23 ft.
0
1
2
3
4
58 ft.
48 ft.
38 ft.
29 ft.
21 ft.
28 ft.
23 ft.
19 ft.
17 ft.
15 ft.
3. In the column listing the type of metal vent you are using (rigid or flexible), find the
maximum length of metal vent on the same line as the number of elbows.
The maximum length using a 2" x 6" rectangular vent with 2 elbows and a 2-1/2"
exhaust hood is 8 ft.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 3405338 Rev. D
01-09-03
|