8. Click Next to accept the Program Folder default, shown below. Files will
then start to be copied to your computer.
1020YV VGA LCD Monitor
1020TSV VGA LCD Monitor w/ Touch Screen
9. Setup will finish installing and tell you that The Touchkit driver has been
installed. Now plug the USB connector from your monitor into your
computer. Click YES to perform 4-points calibration when asked to.
Follow the instruction to touch, hold, and then release each of the four
blinking X to complete 4-points calibration.
10. Your Touchscreen is now ready to use. You can click on the icon Touchkit
located on your desktop to launch the Touchscreen program for various
settings and adjustments.
Owner’s Records
The model and serial numbers are located on the rear of the unit. Please record these
numbers in the spaces provided below, as well as the dealer name, address, and
telephone number. Please refer to these records whenever speaking to your dealer
regarding this product.
Model # _______________________ Serial # ______________________
Dealer Name _________________________________________________
Street Address ________________________________________________
City ___________________ State _______________ Zip ____________
Phone # (
) _________________Purchase Date ____/____/____
External Buttons, Hot keys description:
Install the Touch Screen Driver for Microsoft Windows XP:
Note1: The OSD Menu is only available when a video source is present.
Note2: The Hot keys are only available while the OSD menu is off.
Here is a simple walk through of Windows XP Touch Driver Installation for
1020TSV. You can skip this step if you have the 1020YV.
“M”
“S”
– Stands for Menu. This button is for OSD menu on/off toggling.
– Stands for Select. Use this button to scroll the menu when the
OSD menu is on. Use this button as a hot key to switch video
channel directly when OSD menu is off, following this rotation:
VGA ->Video1 -> Video2 ->VGA.
1. Click on Start, Run, and Enter D:\Driver\Win2000_XP\Setup.exe (Please
change the drive letter corresponding to the drive containing the installation
CD). Click OK.
“/\”
“\/”
“D”
– Stands for Increase. Use this button to increase value while OSD
menu is on. Use this button as a hot key to increase speaker
volume directly when OSD menu is off.
– Stands for Decrease. Use this button to decrease value while
OSD menu is on. Use this button as a hot key to decrease speaker
volume directly when OSD menu is off.
– Stands for Dimmer. Use this button to quickly dim the backlight
for night time use, following this rotation: Full Brightness ->
Medium Brightness -> Low Brightness -> Full Brightness.
2. The Install Wizard window appears. Click Next.
3. Click Next to continue. Please leave the check box next to “PS2
Touchscreen Driver” unchecked.
Remote Control functions Description:
“Menu” – Stands for Menu. This button is for OSD menu on/off toggling.
“
“+”
– Stands for Increase. Use this button to increase value while OSD
menu is on. Use this button as a hot key to increase speaker
volume directly when OSD menu is off.
“–”
– Stands for Decrease. Use this button to decrease value while
OSD menu is on. Use this button as a hot key to decrease speaker
volume directly when OSD menu is off.
“/\”
“\/”
– Stands for Up. Use this button to Scroll up through the OSD
menu while OSD menu is on.
– Stands for Down. Use this button to Scroll down through the
OSD menu while OSD menu is on.
4. Select Next system boot up for 4-Point Calibration and click on Next to
“PIP” – Use this button to enable Picture In Picture function. Press once
for AV1 in PIP window, press twice for AV2 in PIP window, press
again to turn off PIP.
continue.
“POP” – Use this button to enable Split Screen function. Press once for
AV1 in Split Screen, press twice for AV2 in Split Screen, press
again to turn off PIP.
“YES” – Use this button in PIP or Split Screen mode to switch between
the three modes: Small PIP Window, Large PIP Window, and Split
Screen.
“Scan” – Use this button to switch video channel, following this rotation:
VGA ->Video1 -> Video2 ->VGA. Pressing this button in PIP or
Split Screen mode will change the input of the main screen.
On Screen Display functions description:
Internal Specifications:
The OSD can be turn on by pressing the button “M”.
LCD Module
LCD Native resolution
Pixel Pitch
: 10.2” Digital TFT LCD
: 800 x 480 (2400 x 480 dots)
: 0.1905 x 0.1905 mm
Brightness
- Adjust brightness by pressing the Increase/Decrease buttons. Increase the
number for higher brightness. Decrease the number for lower brightness.
LCD Panel Brightness
Contrast
: 500 NIT (max.) / 450 NIT (typ.)
: 300 : 1
Contrast
Response Time
Viewing Angle
Supported display resolution
Supported refresh rate
Video Format
: 12ms (rise) / 18ms (fall)
: Vertical: 110 / Horizontal: 120
: 640 x 480 ~ 1024 x 768
: 60 ~ 75 Hertz
: NTSC/PAL Auto-detect
: 18-bit (262,144 Colors)
: Adjustable output w/ Power Mgmt
- Adjust contrast by pressing the Increase/Decrease buttons. Increase the
number for higher contrast. Decrease the number for lower contrast.
Saturation
- Adjust saturation of color. (Valid in Video 1 in Video 2 only)
Horz Pos
- Adjust Horizontal position by pressing the Increase/Decrease buttons.
Colors
Inverter Inside
Vert Pos
- Adjust Vertical position by pressing the Increase/Decrease buttons.
Electrical Characteristics:
Phase
Absolute Maximum Ratings:
- Adjust CLK phase alignment by pressing the Increase/Decrease buttons.
Image flicker can by avoided by CLK phase adjustment. (Valid in the VGA
mode only)
Auto Detect
- Adjust display automatically. (Valid in the VGA mode only)
Default
- Load default setting.
Dimmer
Parameter
Symbol
Min
Max
1.4
Unit
Vp-p
V
Analog Signal Input Level
Power Supply
Signal
0
DC IN
11
-
24
Digital Signal Input Level
Operation Temperature
-
-
5+0.3
176
V
-14
ºF
- Chose one of the three CCFL backlight output level.
AV2 First
- Set whether to have monitor switch to Video Input 2 automatically if a
signal is present. Good for car reverse monitoring system. Default is No.
Recommended Operating Conditions:
Format
- Select between 16:9 and 4:3 modes. (Valid in Video 1 and Video 2 only)
Mirror
Parameter
Symbol
Min
Typical
Max
Unit
Analog Signal Input Level
RGB/Composite AV
Signal
DC
0.5
GND
11
0.7
-
1.2
0.3
Vp-p
V
- Mirror Image Flip. This function mirrors the display.
Inverse
- Vertical Image Flip. This function flips the display upside down.
DC IN
Current
12
24
V
Power Supply
0.59
0.72
0.74
A
External Specifications:
Video Source Input
Power Consumption:
•
•
RGB analog male connector (15-Pin D-SUB) x 1
RCA composite video female connector x 2
Audio Source Input
Standby mode < 0.3W
Suspend mode < 3W
Continue mode < 4W (w/o inverter), < 9W (w/ inverter)
•
RCA audio female connector x 1
Touch Panel I/O
Inverter output specifications:
•
USB connector x 1 (1020TSV)
Power Source Input
Power supply: +12V
Lamp frequency: 50KHz
Max output open voltage: 1300Vrms
Power consumption: < 5W
•
Single 12V DC_IN (Supports 11V ~ 24V)
|