Yamaha Stereo System 5063 User Manual

Firmware Update Procedure for RX-V467/RX-V567  
September, 2010  
Subject: RX-V467/RX-V567 Firmware Update Version F018  
(Including HTR-4063/HTR-5063)  
Yamaha is pleased to offer the following firmware update to ensure the best possible  
performance and features for your Yamaha RX-V467/RX-V567 AV Receiver. This  
firmware adds 3D video pass-through capability for the HDMI connections and improves  
stability with 3D signals from DirecTV set-top boxes.  
Requirements:  
A personal computer capable of burning an audio CD  
BD/DVD/CD player* with digital audio connection  
(Optical or Coaxial, not HDMI)  
*Note  
CD PLAYER IS PREFERRED.  
Some DVD players use digital filters, which affects the output signal of the  
devices. This firmware update may not work with DVD players which use these  
digital filters. CD players usually do not use these filters.  
CHECK THE UNIT’S FIRMWARE VERSION PRIOR TO THIS UPDATE  
The firmware version consists of a letter followed by three numbers [ex. “F018”].  
If the three numbers in the firmware version are 018 or higher, you DO NOT need to  
perform this update.  
How to check your firmware version:  
Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you  
press the [STANDBY/ON] button. Once the front panel displays "ADVANCED SETUP",  
release the [STRAIGHT] button. Then, press and hold the [TONE CONTROL] button for  
about 3 seconds until front panel display shows the firmware version.  
The following pages contain the firmware update instructions for Yamaha AV receivers  
RX-V467/V567. The outline of the update is as follows:  
1. Create an update disc (Audio CD)  
2. Connect digital audio with CD, DVD or BD player  
3. Enter firmware update mode  
4. Play the update disc (Reprogramming)  
5. Confirm update firmware version  
< IMPORTANT NOTICE >  
Do not attempt to update your Yamaha receiver using any other data file except those provided  
directly from the Yamaha website.  
Follow the instructions carefully and do not attempt any other procedures not specified in the  
instructions provided by Yamaha.  
Improperly updated products may cause improper operation, and any parts or service required  
to restore proper operation will not be covered under the Yamaha Limited Warranty.  
Page.1 of 5 Sep  
 
Firmware Update Procedure for RX-V467/RX-V567  
STANDBY/ON  
INFO  
TONE CONTROL  
STRAIGHT  
STEP3 ENTER FIRMWARE UPDATE MODE  
Plug the AC power cable of the AV receiver.  
Press and hold the [STRAIGHT] button on the front panel and keep it pressed  
while you press the [STANDBY/ON] button. Once the front panel displays  
"Advance Setup", release the [STRAIGHT] button. Then, press and hold the  
[INFO] button for about 3 seconds until front panel displays CDDA Upgrader.  
Now your AV receiver is ready for firmware update.  
STEP4 START FIRMWARE UPDATE  
Turn on the BD/DVD/CD player.  
Load the Firmware Update CD (Audio CD) and press [PLAY] button on the  
BD/DVD/CD player.  
“Found Header” will appear on the AV receiver for few seconds. Then, the  
firmware update starts.  
“Found Header” appears within 10 seconds from starting update disc playback.  
In case display doesn’t change after 10 seconds, retry the update process again  
from the beginning or check requirements for the update disc and connection.  
See IN CASE OF ERROR for details.  
While update is in progress,  
DO NOT interrupt the AV receiver by pressing any buttons or  
switching off the power.  
When completed, “Update Success”, “Please...” and “Power off!!” are  
displayed repeatedly. Turn off the power of AV receiver.  
Stop the BD/DVD/CD player, remove update disc and power off.  
Page.3 of 5  
 
 
Firmware Update Procedure for RX-V467/RX-V567  
STEP5 CHECK UPDATED VERSION  
Press and hold the [STRAIGHT] button on the front panel and keep it pressed  
while you press the [STANDBY/ON] button. Once the front panel displays  
"ADVANCED SETUP", release the [STRAIGHT] button. Then, press and hold  
the [TONE CONTROL] button for about 3 seconds until front panel displays  
“M:F018 66A8.  
F018: version of firmware  
66A8: checksum  
If your firmware version number and checksum don't match, retry from step 3.  
Turn off the power of AV receiver.  
Congratulations!  
You have completed the firmware update. Your AV receiver is ready for normal use.  
Page.4 of 5  
 
Firmware Update Procedure for RX-V467/RX-V567  
IN CASE OF ERROR  
Case1 Display on the receiver “CDDA Upgrader” doesn’t change after playing the  
BD/DVD/CD player.  
Check digital cable wiring. Only optical or coaxial connection can be used for  
this update. HDMI connection will not work.  
Check digital out setting. When using DVD/BD players, make sure the digital  
out is set to “PCM”. Once update is completed, reset DVD/BD player to its  
original settings.  
Check update disc. Make sure that your CD-R/RW is finalized and created  
as an “AUDIO CD”. (playable on any BD/DVD/CD player)  
If all above are cleared, your BD/DVD/CD player may not be suited for this  
update. Try another BD/DVD/CD player or contact your local authorized  
service center to update the receiver for you.  
Case2 Other unintended error occurred.  
"ERROR" was displayed during the update  
Receiver doesn't power up after the update.  
Solution: Try the following recovery method  
Step PL1. Unplug the AC power cable of the AV receiver from wall outlet.  
Step PL2. On the front panel of the AV receiver, press and hold the [INFO] button  
and keep it pressed, while you plug the AC power cable of the Yamaha  
receiver to the wall outlet. Once the front panel displays "CDDA  
Upgrader" release the [INFO] button.  
Step PL3. Go to Step 4 “START FIRMWARE UPDATE”.  
Page.5 of 5  
 
 

Weider Home Gym WESY85290 User Manual
West Bend Fondue Maker ELECTRIC FONDUE POT User Manual
Whirlpool Ventilation Hood RH8330 User Manual
Whirlpool Washer 3953964 User Manual
Whirlpool Washer Dryer 3397612 User Manual
Whynter Fan HAC 100s User Manual
Zanussi Refrigerator 110044 User Manual
Zanussi Washer FR 1250 S User Manual
Zanussi Washer Z468TX User Manual
Zenoah Brush Cutter BC2311LE, BC2611LE, BC2611WE, BC3501LE, BC3501WE, BC4501WE User Manual