REFRIGERATOR-
FREEZER
ZA 33 Y
ZA 33 S
INSTRUCTION BOOKLET
2222 042-33
CONTENTS
Instructions for the User
Instructions for the
Installer
2
4
5
Important Safety Information
Description of the appliance
14
15
Technical specification
Installation
Positioning
Operation
15
15
Before use
5
5
5
5
6
6
6
6
7
7
7
Rear Spacers
Setting the temperature
Freezing fresh food
Storage of frozen food
Thawing
16
17
Electrical Connection
Door Reversability
Making ice cubes
Cold accumulator
Fresh food refrigeration
Movable shelves
Positioning the door shelves
Meat box
8
9
Hints and Tips
Maintenance and Cleaning
Internal cleaning
9
9
9
9
9
External cleaning
When the appliance is not in use
Changing the light bulb
Defrosting
11
12
12
13
Something not working
Service and Spare Parts
Customer Care
Guarantee Conditions
2222 042-33
3
DESCRIPTION OF THE APPLIANCE
A
B
C
K
D
J
I
E
F
3
6
AST FREEZE
F
9
12
H
G
A - Thermostat control for fridge and freezer compartments
B - Dairy compartment
C - Can storage shelf with egg tray
D - Can storage shelves
E - Bottle storage shelf
F - Freezer calendar (recommended storage times for frozen foods)
G - Storing frozen food
H - Freezing fresh food
I - Salad drawers
J - Glass shelf
K - Glass shelves
4
OPERATION
Before using
that, in this condition the refrigerator compartment
temperature might drop below 0¡ C.
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
If this occurs reset thermostat knob to a warmer
setting.
In any 24 hours you can freeze up to 4 kg.
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Place the food to be frozen in the upper drawer of
the freezer as this is the coldest part.
Setting the temperature
Important
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and
one ÇOFFÈ (O) position.
In the event of a power cut do not open the door.
The food in the freezer will not be affected if the
power cut is short and if the freezer is full. Should
the food begin to thaw, it must be consumed quickly
and must not be re-frozen.
Position 1 = minimum coldness
Position 6 = maximum coldness
Turn the thermostat dial to the required position.
The intermediate position is usually the most
suitable (3-4).
Storage of frozen food
When first starting-up or after a period of use, before
putting the products in the compartment let the
appliance run for at least two hours on the coldest
setting, then turn the thermostat knob to the normal
operating position.
The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:
Ð room temperature
Ð how often the door is opened
Ð how much food is stored
Ð position of the appliance
Do not exceed the storage period indicated by the
manufacturer.
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
Important
Important
If the fridge is not defrosting correctly, it is possible
that because a very low temperature has been
selected, the motor is working continuously, which
prevents the defrost cycle from operating.
Do not put carbonated liquids, (fizzy drinks etc.), in
the freezer compartment.
Ice Iollies, if consumed immediately after removal
from the freezer, can cause low temperature skin
burns.
To ensure correct defrosting, a lower number should
be selected on the thermostat and you should notice
that the motor cuts out from time to time, which is
correct.
Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions or
Òfrost/freezer burnsÓ.
If you wish to return to a lower temperature, turn the
thermostat to a higher number, however you should
turn the setting lower occasionally to allow automatic
defrosting.
The freezer compartment
The four-star freezer compartment is suitable for
storage of commercially frozen food and for freezing
fresh foods.
Freezing fresh food
To freeze fresh foods it is not necessary to change
the setting of the thermostat knob.
However, for a quicker freezing operation, turn the
thermostat knob to the coldest setting; but remember
5
Thawing
Fresh food refrigeration
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Deep frozen or frozen food, prior to being used, can
be thawed in the fridge or at room temperature
depending on the time available. Small food items
may even be cooked from frozen; in this case
cooking will take longer.
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
Any frozen food which is allowed to thaw
accidentally should either be eaten as soon as
possible or thrown away. Alternatively, if the food is
uncooked and has not been completely defrosted it
can be cooked and then refrozen.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & wild fowl): wrap in
polythene bags and place on top of the salad
crispers.
Meat, fish and fruit should be thawed in the
refrigerator compartment and small pieces of meat
can even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
Meat can only be stored safely in this way for
one or two days at the most.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad crispers.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
A microwave oven is particularly suitable for thawing
any type of frozen or deep-frozen food: follow the
oven instructions, particularly regarding the
placement of aluminium wrapping or containers in
the oven.
Milk bottles: these should have a cap and should
be stored in the bottle rack on the door.
Defrosted cooked food must never be refrozen.
Making ice cubes
The appliance is provided with one or more trays for
the production of ice-cubes.
Fill the trays 3/4 full to allow the ice to expand and
place them in one of the freezer compartment.
Do not use sharp instruments to remove the trays
from the freezer.
To remove the cubes twist the tray slightly or hold it
under running water for a few seconds.
Cold accumulator
The freezer contains two cold accumulators which
can be found in one of the freezer drawers. Place
the cold accumulator in the FAST FREEZE
compartment. The cold accumulator increases
storage times in the event of power cut or
breakdown.
Removal of this unit will increase the capacity of the
fast freezing compartment but will reduce storage
times in the event of a power cut or breakdown.
6
Movable shelves
The walls of the refrigerator are equipped with
runners so that shelves can be positioned as
desired.
For better use of space, the front half-shelves can lie
over the rear ones.
D338
Positioning the inner shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To make these adjustments proceed as follows:
Gradually pull the shelf in the direction of the arrows
until it comes free, then reposition as required .
PR261
For more thorough cleaning, the top door shelf can
be removed by pulling it in the direction of the
arrows, then refitting it in position.
PR263
Meat box
The meat box can also be used as a salad crisper.
7
HINTS AND TIPS
Energy Saving Advice
Normal Operating Sounds
¥
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
plate/evaporator.
¥
¥
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
¥
¥
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
¥
Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight pakages before
placing them in the freezer.
A thermostat controls the compressor, and you
will hear a faint ÕclickÕ when the thermostat cuts in
and out.
¥
¥
Always leave warm food to cool down to room
temperature before placing in the fridge.
Food Storage
Food which is to be frozen (when cool) should be
placed in the fridge before being transferred to
the freezer.
To obtain the best performance from your fridge-
freezer
¥
¥
Thaw frozen food in the fridge. This will ensure
safer defrosting of foods and reduce the work of
the refrigeration unit.
¥
¥
Do not store warm food or evaporating liquids.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container
is advisable. When you arrive home place the
frozen food in the frezeer immediately.
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
¥
¥
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
¥
Ensure there are no obstructions preventing the
door from closing properly.
Do not push food together too much, try to allow
air to circulate around each item.
In the Event of a Power Failure
¥
¥
Do not store food uncovered.
If there is a power failure during the storage of frozen
foods, keep the door closed. If the temperature
within your freezer should rise, do not refreeze the
food without checking its condition. The following
guidelines should assist you:
Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
¥
¥
¥
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
Ice-cream: Once thawed should be discarded.
Lean food keeps better and longer than fatty
food, salt reduces the storage time.
Fruits & Vegetables: If soft should be cooked and
used up.
Wrap the food in polythene or aluminium freezing
bags or foil so that they adhere to the food and
provide an airlight seal .
Breads & Cakes: Can be refrozen without danger.
Shellfish: Should be refrigerated and used up
quickly.
¥
Packaging which is swollen or has traces of
refrozen water droplets on the pack could
indicate that the product has not been kept at a
suitable temperature and that it may have lost its
original quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage times indicated by the
manufacturer.
Cooked Dishes: i. e. casseroles should be
refrigerated and used up.
Large Pieces of Meat: Can be refrozen providing
there are still ice crystals remaining within them.
Small Joints: Should be cooked and can then be
refrozen as cooked dishes.
Chicken: Should also be cooked and refrozen as a
fresh dish.
8
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
Changing the light bulb
Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity
supply, then replace the bulb as follows;
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED
CLEANING PRODUCTS OR WAX
POLISHES, TO CLEAN THE INTERIOR AS
THESE WILL DAMAGE THE SURFACE AND
LEAVE A STRONG SMELL.
D731
External cleaning
Unscrew the light cover and then pull it outward by
pressing as shown in the figure. Unscrew the bulb
and replace it with a new 15 watt bulb (available
from your nearest Service Force Centre).
Wash the outer cabinet with warm soapy water. Do
NOT use abrasive products.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
Replace the light cover by sliding it into its original
position and replacing the screw.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
Defrosting
Refrigerator
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
CONDENSER
DEFROST
TRAY
COMPRESSOR
D273
D037
When the appliance is not in use
Important
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of the
refrigerator compartment behind the fruit and
vegetable drawer. Use the defrost cleaner provided
which you will find already inserted into the discharge
hole.
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry throughly before
replacing.
9
Freezer
When the frost has reached a thickness of up to
4mm it can be removed using the ice scraper
provided with the appliance. During this operation it
is not necessary to disconnect the appliance from
the mains and remove the food. Never use metal
tools for this operation.
For complete defrosting (once or twice a year)
proceed as follows:
-
turn the thermostat dial to the ÇOFFÈ position (O)
or disconnect the appliance from the mains.
-
Remove any food from inside the freezer and
fridge, wrap it in several sheets of newspaper and
store in a cool,dry place.
-
Leave the door open and insert the ice scraper
under the channel in the centre of the lower part
of the appliance; place a low-sided container
beneath the scraper to collect the water (see fig.).
-
-
-
Clean and dry thoroughly.
Replace the scraper in one of the drawers .
Reconnect the appliance to the mains or reset
the thermostat to a functioning position.
D068
-
After letting the appliance run for a least half an
hour, replace the previously removed food into
the compartment.
Important
When defrosting the freezer, the fridge is also
controlled by the thermostat and will not be
operational during this period. A temperature rise of
the frozen food packs, during defrosting, may
shorten their safe storage life.
10
SOMETHING NOT WORKING
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation a charge will be made, even if the appliance is under guarantee.
Before contacting your local Service Force Centre, check the following points:
Symptom
Solution
No power to the appliance
Check there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
The light does not come on
Ensure that the bulb is correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
The temperature in the fridge or freezer section is
too high
Check the temperature in the fridge is turned to the
correct setting relative to ambient conditions.
Check the ambient temperature is within the
applianceÕs operating limits of 10¡C to 32¡C.
The freezer door will not open
Has door just been opened? If so leave for a few
minutes to allow the air pressure to equalise.
The compressor runs continously
Adjust the thermostat to give correct temperature
control. See ÒSetting the temperatureÓ.
Check that the doors are closed.
Large quantities of food have recently been placed in
the cabinet/and or door is frequently opened.
Check that air ventilation is not obstructed.
Ensure the doors are not left open.
Excessive frost and ice has built up
Check that nothing is preventing the doors from
closing.
Is the door gasket intact and clean.
Has advised periodic defrosting been carried out.
Noise
Refer to normal operating sounds.
Water under the salad bin
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
If, after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service call.
11
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For further details please see the accompanying Customer Care Booklet.
Before calling out an engineer, please ensure you have read the details under the heading ÔSomething Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
2.
3.
4.
5.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please
contact our Customer Care Department by letter or telephone as follows:-
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727 727
12
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturerÕs
instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or
defective part replaced shall become the CompanyÕs property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
+39 (0)1678 47053
+46 (0)8 738 79 50
+44 (0)1753 219 897
NŸrnberg
Pordenone
Stockholm
Slough
Sweden
UK
13
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
185
cm
Width
Depth
60
60
cm
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
220-240 V / 50 Hz
150 W
AVERAGE DAILY UNITS ELECTRICITY *
GROSS CAPACITY
1.10 kWh
Fridge
217 l
88 l
Freezer
NET CAPACITY
Fridge
212 l
77 l
Freezer
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
14
INSTALLATION
Warning
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on ÒDoor reversal directionsÓ paragraph.
Positioning
This appliance is designed to operate in ambient
temperatures between 10¡C (50¡F) and 32¡C (90¡F).
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme temperature
e.g. not next to a boiler or radiator, or in a very cold
room e.g. an outhouse, where the temperatures may
fall below 10¡C (50¡F). If these temperatures are
exceeded i.e. colder or warmer, then the appliance
may not operate correctly.
A
B
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be at least 100 mm (4Ó) distance between
the top of the cabinet and any overhanging kitchen
furniture (A). Ideally, the appliance should not be
positioned beneath overhanging furniture (B).
NP002
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
install in places with restricted ventilation.
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers (see figure).
D200
Rear spacers
In the bag with the documentation, there are two
spacers which must be fitted as shown in the figure.
Slacken the screws and insert the spacer under the
screw head, then re-tighten the screws.
PR153
15
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
Electrical connections
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre whose
address is listed in the Customer Care Booklet which
accompanies your instruction manual.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
-
-
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Important
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not
correspond with the markings identifying the
terminals in your plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
BROWN
BLUE
CORD CLAMP
D207
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
ÇEÈ or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter ÇNÈ or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter ÇLÈ or coloured
red.
The plug moulded onto the lead incorporates a fuse.
16
Door reversibility
1. Unplug the appliance from the power supply
before carrying out the following operations.
E
E
2. Pull off the ventilation grill (D).
F
F
3. Remove the plug (F) from the ventilation grill (D)
and replace it on the opposite side.
4. Remove the bottom hinge (E) by unscrewing its
three fixing screws.
D
F
5. Remove the freezer door by releasing it from the
middle hinge (H).
PR18
6. Unscrew the middle hinge.
7. Remove the fridge door by releasing it from the
top hinge pin (A).
C
B
8. Remove the pin and the washer (A+B) from the
top hinge (C), then mount these on the opposite
side.
A
9. After having removed the plugs which must be
fitted on the other side, refit the fridge door.
10.Replace the middle hinge to the left hand side.
11.Replace the freezer door.
D736
12.Using a 10 mm spanner, unscrew the hinge pin
(E) and reassemble it on the opposite side of the
hinge.
13.Refit the bottom hinge (E) on the opposite side by
of the appliance using the screws previously
removed.
14.Refit the ventilation grill (D) to the base of the
cabinet.
15.On the side where the handle is to be fitted, push
in the blanking cover caps to free the new holes.
Remove the handles and refit them on the
D737
opposite side. Cover the holes left open with the
plugs contained in the documentation pack.
H
The doors can be aligned by adjusting both the
middle and top hinges.
The middle hinge can be adjusted horizontally, after
having slackened the two screws.
The top hinge is adjusted by slackening the nut with
a 10 mm spanner and then proceeding as shown in
the figure.
Attention
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdrier on a low setting.
17
|